Improvements in drilling make manufacturing more efficient
Hole drilling plays a critical role in automotive manufacturing. Hundreds of holes must be drilled for each vehicle that’s manufactured, including those in transmission shafts, engine blocks, air bag propellant chambers, camshafts, and other internal engine parts. In any automotive vehicle part production line, conveyor belts are running nonstop and efficient tools are a key aspect of profitability.
Every minute a spindle is not drilling holes, or is not efficiently evacuating the chips formed from drilling, is a minute when money is lost. Manufacturers must take advantage of seemingly small tooling changes because they can make a huge difference in holemaking efficiency. Innovative technology is now available that can be integrated right into a process seamlessly without shutting production down. Adopting these innovations that decrease costs can significantly increase margin dollars for the company.
Incorporating Tooling into Vehicle Manufacturing
In the past, all large, high-volume automotive metalcutting and drilling operations were performed with transfer lines on dedicated machines. These machines had set running speeds with large chains that conveyed parts between machining stations, where they waited for the operation to be performed. A set number of parts could be drilled in a day; in addition, if one machine broke down, the entire line shut down. There was no advantage in developing cutting or drilling tooling that hastened operations because the line was only able to run at its designated speed.
This antiquated approach to automobile manufacturing continued throughout the 1970s and 1980s but slowly began to change in the 1990s, with the rise of computer numerical control (CNC) machines. Today’s modern automobile manufacturers are now using flexible CNC equipment; if parts can go faster on one machine, they can be sped along to the next one, perhaps gaining an advantage that ultimately translates into higher revenue.
With these new CNC-operated transfer lines, manufacturers can be more flexible, making changes and taking advantage of any new tooling that comes out. They can incorporate tooling innovations that help them increase production and make more money. Those in the tooling industry are therefore always looking for new and innovative tools that can speed up the slowest part—the one that is holding back other operations—to yield significant overall cost savings.
Industry Trends Affecting Metalcutting
One major factor affecting metalcutting in the last 20–30 years is the long-term elimination of free machine metals, those that can be cut easily, allowing material removal with a satisfactory finish at low cost and without wearing out tooling. With the removal of lead in metals and the replacement of cast iron with compacted graphite iron (CGI), the metals used in the automotive industry have gone from machine friendly to extremely difficult to machine.
This means that tooling must be adjusted to increase chip control to gain tool life and make the hole straighter. Other related industry changes that affect hole-drilling tooling are the environmental laws limiting the use of chlorine and sulfur in hole drilling coolant systems. (The scope of this problem is different in Europe, which requires dry-machining, in which no coolant, or very little, is used, because elimination of waste coolant is prohibited by pollution laws.) The elimination of chlorine and sulfur has resulted in an increase in problems with chip build up on the cutting tool, chip sticking, and reduced tool life.
The end result is that tooling manufacturers have to find innovative ways to deal with these trends. Tooling manufacturers have had to innovate to improve their tools’ performance. Some companies are moving towards near-net forging to avoid these issues, but the problems will continue, since parts will always differ from forger to forger.
In response to these automobile manufacturing, economic, and environmental/regulatory trends, the market is looking for innovations in turning and drilling—both machines and tooling. In effect, this innovation is what makes money for an automotive manufacturer.
For example, new turning and drilling machines are coming on the market with high-speed tool changing and more accurate HSK (hollow taper shank) tool spindles. But there are also many opportunities to design tooling that make up for deficiencies on older machines. Placing 21st century tooling on 20th century machines can significantly improve manufacturing efficiency and increase profitability, making older machines perform like brand-new ones. Improving an existing capital asset can be a huge advantage, since capital requests for major new equipment purchases can be difficult to fund. With the flexibility of new CNC machines, new tooling improvements can be integrated seamlessly—without shutting down the production line to retool.
One example is the engineering and design work that Allied Machine & Engineering performed for a Tier 1 supplier to a major automotive manufacturer on a high-volume transmission shaft made of steel alloy, a poor chip-forming material. The existing tool used a low tool pressure coolant system and small spindle tapers. It created a very large and abrasive chip, which trapped itself on the outer dimension of the drill’s holder body, laying in the bottom of the hole and not evacuating. With a poor hole surface finish, the tool could drill only 200–400 holes per insert and had a high monthly scrap of about $20,000.